Troubleshooting

Common problems and their fixes: the site is not updating, publishing failed, the domain does not open, the AI is not doing what you asked.

Last updated: 5 min read

These are the questions support gets most often. Most of them you can resolve yourself in a couple of minutes.

My site did not update

You made a change but it is not on the live site. Check in order:

  1. Did you publish? Changes do not reach the site on their own. Blog posts, products, plugins and design edits all need a Publish.
  2. Did publishing actually finish, did you see it complete successfully on screen?
  3. Hard refresh the page: Ctrl + F5 on Windows, Cmd + Shift + R on Mac.
  4. Open it in a private window. If it looks right there, it is your browser's stored copy.

For details, see Publishing and updating.

Publishing failed

Entrobase first tries to fix a build error on its own; if it cannot, the publish stops. Your live site usually stays as it was. If the failure happens in the last step, part of the new version may already be live; publish again.

  1. Press Fix with AI in the publish window. The error goes to the chat and the AI attempts a fix.
  2. Publish again when the fix is done.
  3. If the same error repeats three times, press Restore this version on the reply before your last big change, publish, then reintroduce it in smaller steps.

The AI is not doing what I asked

  • Split the request. If you asked for several changes at once, ask for them one at a time.
  • Say where. Point at a place: "the heading at the top", "the button in the contact section".
  • Send a screenshot. Upload an image of the problem area and describe what you want.
  • Check the mode. If the mode in the chat box is Chat, the AI does not change code and only answers. Switch to Auto or Build.
  • Switch models. If three attempts failed, move to a stronger model.
  • It may not be possible. Payments, carts and a separate admin panel are not written by chat, and there is no plugin for them yet (EntroCommerce is coming soon).

My domain does not open

  • After adding the record, propagation usually takes 15 minutes to an hour, and up to 24 hours with some providers.
  • Delete any old A or CNAME records still sitting in your provider's panel.
  • Make sure both CNAME records (root address and www) and the _entrobase-verify TXT record were added.
  • If you never published the project, the domain will not open anything even when connected.

For details, see Connecting a domain.

My blog post is not on the site

You wrote and saved the post but it is not live. That is expected: posts do not reach the site until you publish.

  1. Make sure the post's status is Published.
  2. Publish the project.
  3. Check your site in a private window a few minutes later.

I hit my usage limit

  • Your live site is unaffected and stays online.
  • The weekly limit resets at the start of the next week.
  • If you do not want to wait, upgrading applies immediately.
  • You can track usage on Settings › Usage and on the Credits page in the account menu.

For details, see Plans and usage.

Form e-mails are not arriving

First look at the Forms page in the left menu. If the submission is there, the form works and only the e-mail is the issue.

  • Open the submission: its e-mail status is shown (sent, queued, waiting for the daily summary and so on).
  • If your monthly or daily notification allowance is used up, submissions are still saved and notifications arrive in one daily summary e-mail.
  • No e-mail is sent for submissions in the Spam and Test tabs. Tries from the Builder preview land in the Test tab.
  • Check that Email notifications is on in the settings. Notifications go to your account e-mail; check your spam folder too.
  • If the submission is not on the Forms page at all, publish the site once more and make sure Accept forms is on.

For details, see Forms.

My app does not open on my phone

  • Expo Go must be installed on your phone. The QR code becomes sharp once the preview is ready; do not scan it while it is blurred.
  • On iPhone scan it with the Camera; on Android use "Scan QR code" inside Expo Go.
  • If changes do not arrive, reload the app in Expo Go.
  • If Expo Go says the project is not compatible, update Expo Go from the store.

For details, see Mobile apps and Expo Go.

I cannot sign in

  • If the code did not arrive, wait a few minutes and check your spam folder.
  • The code may have expired; request a new one.
  • If you signed up with Google or GitHub, sign in the same way.
  • Check the address you typed; a different address creates a new account.

A document I added to the chat is not read

  • The text of an image-only (scanned) PDF cannot be read. Add a photo or screenshot of the page as an image instead.
  • Files larger than 20 MB are not added; make the file smaller or move the part you need into a separate file.
  • .env files are never added because they can hold secret keys.
  • If the document is very long, only part of it is read and the screen says so. Name the part you care about in your message.
  • More: Adding documents to Entro.

Still stuck

When you write to info@entrobase.ai, include your project name, the step you got stuck on, the error message on screen (with its error ID if there is one) and a screenshot. That way we can understand the problem from your first message.

Was this page helpful?

Still stuck?

If this article did not solve it, email support; the article name is added to the subject line.

info@entrobase.ai
Email support
All prompts